http://www.northlandmarine.com/MinnKotaQuickRef.htm has parts, wiring diagrams, props etc for MinnKotas, even solid state control boards which I don't doubt could be adapted for any brush-type within their amp limitations. They're not cheap though, and could be an expensive experiment.
That said, I would suspect that the "resistor" motors might actually be MORE efficient at full power, when all the resistors should be out of the circuit (haven't had one apart yet though). The PWM models would still be running the power through the board, with some loss even at full speed. A bypass switch might be in order for cruise mode.
--- In electricboats@yahoogroups.com, oak <oak_box@...> wrote:
>
> FYI...   When I did my testing on the Traxxis 80 Minn-Kota, I noticed that the control head got pretty darn hot to the touch after running for about 45 min at mostly 75% to 100% speed. So be careful!   :)
> Â
> I liked the response about the resistors that indicated it wasn't such a bad thing for all applications.
> Note - the resistors increase the overall resistance of the load.  If the resistance is increased for the same battery voltage, the current drops.  Overall power is LESS.  Yes, you're dissipating power in heat that wouldn't necessarily be burned in a PWM unit.  But for small motors, the loss of efficiency is most likely outweighed by the lack (and cost) of the complexity of a more efficient unit.Â
> Â
> A trolling motor small enough to use resistors in it's controller would still run a very long time at low power on a car sized battery (which is what most Jon boats would probably have). It accomplishes the typical need at low cost.
> Â
> At high speed, it's a wash.
> Â
> The question is whether trolling motors were allowed in their design to be run at full power for LONG periods of time (2+ hours)??
> Â
> The other interesting factor about this thread is that it's sounding like the props put on trolling motors are pitch limited (at the max speed of the motors) to around 3.5mph. Â
> Â
> I'd be really curious to try a 10x6 prop on a trolling motor - as suggested.  I'm also curious to see if that will burn out the motor if run at full speed for over an hour.
> Â
> John
>
>
> ________________________________
> From: R&M Mair <fullkeel2000@...>
> To: electricboats@yahoogroups.com
> Sent: Sunday, June 16, 2013 4:28 PM
> Subject: Re: [Electric Boats] Re: Minnkotas
>
>
> Â
>
> Thanks for all the info. Looks like for this summer I will just run wide open. I will have to decide weather to start trying props to see weather the speed difference is worth it. I use this on our dinghy and I can row faster when alone than the motor pushes us.
> We will be travelling all summer by boat. More about this later.
> Richard
>
> Carel Ruysink <mailto:c.ruysink%40hetnet.nl> wrote:
>
> >There are a lot of good electronic speed controllers (ESC) also in the 12V range and high power ratings in the modelairplane modelcar industry (ao Hobby King).
> >For modelcars and boats they have forward and reverse, for modelairplanes they only have forward.
> >The only drawback is they are wireless (transmitter and receiver) maybe even an advantage when not close to the troller.
> >There are also simple wired servotesters wich you can use to controll your ESC.
> >If you know someone with rather basic knowledge of electronics it is rather easy to alter the ESC to manual operation.
> >Just look around and google.
> >
> >Succes, Carel
> >ps; Model ESCs are for short energybursts 5 min max so look for an ample safetymargin. Eg 250 watt (twice the power for a standard human wich is ample for a small sleek boat) I would choose an 700 to 800 watt Controller.
> >Resistor controllers allways use max power and destroy the energy that you do not want that moment, such a waste (and heat).
> >
> > ----- Original Message -----
> > From: Kirk McLoren
> > To: mailto:electricboats%40yahoogroups.com
> > Sent: Sunday, June 16, 2013 4:26 PM
> > Subject: Re: [Electric Boats] Re: Minnkotas
> >
> >
> >
> >
> > I wouldn't use that one, it was an example of what to search for.
> >
> >
> >
> >
> > remember you are unique. Just like the rest of us.
> >
> >
> >
> >
> >
> >----------------------------------------------------------
> > From: Eric <mailto:ewdysar%40yahoo.com>
> > To: mailto:electricboats%40yahoogroups.com
> > Sent: Sunday, June 16, 2013 2:37 AM
> > Subject: [Electric Boats] Re: Minnkotas
> >
> >
> >
> >
> > Excellent solution, if you never plan on exceeding 96W (about 0.15hp) at full power.
> >
> > Eric
> > Marina del Rey, CA
> >
> > --- In mailto:electricboats%40yahoogroups.com, "Kirk" <kirkmcloren@> wrote:
> > >
> > >
> > >
> > > --- In mailto:electricboats%40yahoogroups.com, R&M Mair <fullkeel2000@> wrote:
> > > >
> > > > I have seen info on here that the cheaper minnkota motors use resistors to control speed. Anyone notice significant run times between full speed and lower speeds?
> > > > Richard
> > > >
> > > http://www.amazon.com/LEDwholesalers-Dimming-Controller-LED-Lights/dp/B003L4KKF2/ref=pd_sim_hi_3
> > >
> > > this one is only for 12 volts but when you see how cheap it is using resistors is silly.
> > >
> >
> >
> >
> >
> >
> >
> >
>
| Reply via web post | Reply to sender | Reply to group | Start a New Topic | Messages in this topic (10) |
No comments:
Post a Comment