[Attachment(s) from Aaron included below]
I am thinking I will be able to cut in a 20" opening so that should give me room for a 16" prop. Maybe I can get 18" It just depends on how I cut the skeg.
From: Eric <ewdysar@yahoo.com>
To: electricboats@yahoogroups.com
Sent: Tuesday, September 20, 2011 2:17 PM
Subject: Re: [Electric Boats] 3201 BROWNING GEARBOX
Hi Aaron,
For a 10kW system, a 3301 seems like the right selection from the Browning Helical gearbox line.
Since you're building the boat from scratch, you might be able to work in a larger prop. It would take a bigger reduction ratio, but it should be more efficient (on the general theory that larger slower props are more efficient). Browning has gear ratios past 5:1 for their gear boxes.
I had to enlarge my aperture just to fit my 13 x 15.5 prop as part of my conversion. Given that maximum prop size, the ratio that James selected of 2.55:1 seems to strike an effective balance between power and speed across my normal operating range.
Eric
--- In electricboats@yahoogroups.com, Aaron <akenai@...> wrote:
>
> I am back looking at installing an electric motor in the 36' steel sailboat I am building. 31' LWL, 10'6" Beam, 10 ton disp. I have a used Westerbeke 44B 40hp diesel but would rather not use it.
> EBay has a 3201 gearbox but I was thinking it was too small.
>
> From: James Lambden <james@...>
> To: electricboats@yahoogroups.com
> Sent: Tuesday, September 20, 2011 10:25 AM
> Subject: Re: [Electric Boats] 3201 BROWNING GEARBOX
>
>
> Aaron,
>
> The limitation is most often the continuous thrust rating of the bearing at the back of the motor, though torque and input rpm are issues too.
>
> The 3301 is rated at 550 lbs of continuous thrust and the 3401 is rated at over 1,000.
>
> The larger gearboxes can't spin as fast as the smaller gearboxes.
>
> What is the torque of the motor, and the rpm where you are producing that much power?
>
> We don't exceed 2,000 input rpm with the gearboxes we use on our units, and most often set the drive up at 1900 rpm.
>
> James
>
>
> http://www.propulsionmarine.com
------------------------------------
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/electricboats/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/electricboats/join
(Yahoo! ID required)
<*> To change settings via email:
electricboats-digest@yahoogroups.com
electricboats-fullfeatured@yahoogroups.com
<*> To unsubscribe from this group, send an email to:
electricboats-unsubscribe@yahoogroups.com
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/
To: electricboats@yahoogroups.com
Sent: Tuesday, September 20, 2011 2:17 PM
Subject: Re: [Electric Boats] 3201 BROWNING GEARBOX
Hi Aaron,
For a 10kW system, a 3301 seems like the right selection from the Browning Helical gearbox line.
Since you're building the boat from scratch, you might be able to work in a larger prop. It would take a bigger reduction ratio, but it should be more efficient (on the general theory that larger slower props are more efficient). Browning has gear ratios past 5:1 for their gear boxes.
I had to enlarge my aperture just to fit my 13 x 15.5 prop as part of my conversion. Given that maximum prop size, the ratio that James selected of 2.55:1 seems to strike an effective balance between power and speed across my normal operating range.
Eric
--- In electricboats@yahoogroups.com, Aaron <akenai@...> wrote:
>
> I am back looking at installing an electric motor in the 36' steel sailboat I am building. 31' LWL, 10'6" Beam, 10 ton disp. I have a used Westerbeke 44B 40hp diesel but would rather not use it.
> EBay has a 3201 gearbox but I was thinking it was too small.
>
> From: James Lambden <james@...>
> To: electricboats@yahoogroups.com
> Sent: Tuesday, September 20, 2011 10:25 AM
> Subject: Re: [Electric Boats] 3201 BROWNING GEARBOX
>
>
> Aaron,
>
> The limitation is most often the continuous thrust rating of the bearing at the back of the motor, though torque and input rpm are issues too.
>
> The 3301 is rated at 550 lbs of continuous thrust and the 3401 is rated at over 1,000.
>
> The larger gearboxes can't spin as fast as the smaller gearboxes.
>
> What is the torque of the motor, and the rpm where you are producing that much power?
>
> We don't exceed 2,000 input rpm with the gearboxes we use on our units, and most often set the drive up at 1900 rpm.
>
> James
>
>
> http://www.propulsionmarine.com
------------------------------------
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/electricboats/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/electricboats/join
(Yahoo! ID required)
<*> To change settings via email:
electricboats-digest@yahoogroups.com
electricboats-fullfeatured@yahoogroups.com
<*> To unsubscribe from this group, send an email to:
electricboats-unsubscribe@yahoogroups.com
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/
__._,_.___
Attachment(s) from Aaron
1 of 1 Photo(s)
MARKETPLACE
.
__,_._,___
No comments:
Post a Comment