Ric,
Mine is bigger than the prototype at 4 meters. I also beefed up the gunwhales a bit to handle the scrum at the dinghy dock. Designer is an Aussie, Craig Clos. He has several videos on YouTube https://m.youtube.com/watch?v=SA6cDk2Imb0&t=3s&pp=ygUTbWFnaWMgY2FycGV0IGRpbmdoeQ%3D%3D
He made the plans for me and was very helpful. I lost contact with him shortly after he launched the 8 meter powercat (full interior, trialed at 22 kts on 2x30 hp Honda with 4 peeps). He had some health problems so I fear the worst. I'll keep trying to track him down. Last address he used was apc.tender@gmail.com
For my boat next step is final structural taping and float in water to figure out weight and balance so I know where to put seats. I've given up on electric motors for now. I'll wait for better stuff. Gonna start with gas Yamaha 8.
Jerry
On May 2, 2024, at 2:04 PM, Ric Sanders <rsandersemail@gmail.com> wrote:
John,
I'm building a 12 foot cat dinghy out of foam and glass. About 120 lbs. I also have the Hang Kai 1.2. Hopefully will have the boat running by end of summer.
I'm probably going to go with a small server rack lifepo4 that weighs about 40 lbs so I can carry it home to charge. The prices are getting better so waiting until end to buy it.
The 10 foot version of my dinghy would plane at 14 knots with one guy on a 3 hp gas honda. So I asked my Aussie propeller expert to look at the Hang Kai. He thinks we'll get at least 10 knots. So I'll give it a shot. If it looks promising I might get another and gang them together. Would also be good for redundancy.
We discussed the prop. The motor is geared one to one, so the prop is spinning at 3000 rpm or so. That's why it's small. Depending on how things go I've got an idea of an adapter to gear it down and fit a bigger prop.
Keep posting. I'll let you know how it goes when we get the thing in the water.
Jerry Barth
On April 18, 2024, at 10:03 PM, "john via groups.io" <oak_box=yahoo.com@groups.io> wrote:Revisiting this question:I'm using an electric motor and battery for my dinghy.I've used Anderson connectors (100A and 50A) - and they're fine electrically.But the 50A blue Anderson connectors corrode horribly in the salt environment.I've seen XT60 and XT90 connectors, and think I've heard of people using those for solar connections (as well as being used in RC stuff).Would XT60 connectors do better in a salt environment than Anderson connectors?JohnOn Friday, June 2, 2023 at 08:00:35 AM CDT, Matt Foley <matt@sunlightconversions.com> wrote:Hi John,I use 50 amp andersons on my dinghy motor. They do take a beating. I have to clean them every few months. Keep in mind, I get them wet frequently and they have taken more than a few dips in salt water. Salt water corrodes them pretty quick. Ill eventually try another solution.I can't speak for the Hankai specifically, but 800 watt input power should be enough for 4mph with a little margin. Power needed to go faster then 4mph will go up exponentially.Matt FoleySunlight ConversionsPerpetual Energy, LLC201-914-0466ABYC Certified MarineElectrical TechnicianOn Friday, June 2, 2023 at 08:36:47 AM EDT, john via groups.io <oak_box=yahoo.com@groups.io> wrote:I'm planning to use an electric outboard on the West Marine RIB 310 for my trawler. The dinghy is about 10' long, weighs a little over 100 pounds empty, plus 2-3 "solid sized" adults, plus motor and battery. Current plan is to experiment with a 48V Hangkai electric outboard, powered by a BTR 48V Ebike battery.Question: What connectors are best for using in the marine environment?I have experience with Torqeedos, and they use Anderson Plugs. Is that the best option for being able to quickly plug between the battery and the motor?One thing I want to do is put a small box between the battery and motor. The box will include a battery switch on the positive leg and a Victron battery monitor on the negative leg. While the Torqeedo used Anderson type connectors, I believe 120A type - I'll probably go with 50A Anderson connectors for the Hangkai. This is because both the batteries and the motor use small guage leads - 12GA at most. This is challenging enough to crimp into the pins of the 50A connector (intended for 8ga wire). I have a crimper that I use for most of the large pins and terminal lugs, but have to resort to using a bench vice to crimp the connectors on the small motor and battery leads. I'm planning to use 8 ga wire for the longer runs. The motor is rated at 1000W. I'm assuming I shouldn't be running much over 20A peak, probably more like 800W for typical cruising.The Hangkai is tiny compared to the Torqeedo 2T. But I'm really curious to see how the Hangkai does, and am REALLY hopeful that it works out. At $350, it's less than 1/10th the cost of a Torqeedo. The Ebike 48V batteries seem to be much better priced and much more available than 24V lithium batteries. My hope is that a 50A Ebike battery will get me at least 2 hours of run time at around 800W on the Hangkai - and I'm REALLY hopeful that 800W will be enough to push the dinghy at least to 3-4mph.I'm looking forward to being able to put some data together to compare the Torqeedo to the Hangkai. I understand that the Hangkai has less than half the power of the Torqeedo (and the prop on the Hangkai also seems tiny compared to the Torqeedo prop) - but if it can honestly put out what it claims to do, I think that'll be sufficient for a small dinghy. Given my battery bank, 800W would be a good burn rate. I know it'll never get me on plane or win any races. But if it gets me from the boat to the beach, and lets me toodle around a little from time to time, that'll be just fine.John
Groups.io Links:
You receive all messages sent to this group.
View/Reply Online (#32627) | Reply To Group | Reply To Sender | Mute This Topic | New Topic
Your Subscription | Contact Group Owner | Unsubscribe [newarmyguitar24@gmail.com]
No comments:
Post a Comment