I'd be interested in 48v 90ah for my boat!
Hello Steve, sorry for the delay. I can sell you some of my extra cells. 3.2 v 90 ah I am happy with my 10 kw 48v thunderstruck project We are experimenting with cylinders and prisms for my work projects. I can assemble and charge (cost only for a bms and bus bars.) We are adding a phase change material to our boxes to minimize possible heat and waterproof my battery packs. It is a simple blend of paraffin wax and synthetic bees wax. All my projects are experimental at this point. Observed performance is our goal. We do not sell anything commercially. cost only if you are interested. 24v 36v or 48v available we can parallel 90 180 270 or 360 ah I use new West Marine heavy guage plastic battery boxes.I will send some pictures tomorrow. I hope this helps.
Terminalift LLC9444 Mission Park PlaceSantee, CA 92071Ph: (619) 562-0355F: (619) 562-2060On Sunday, May 31, 2020, 07:53:28 AM PDT, Steve Gjertson <sgjertson@gmail.com> wrote:Hi Larry,I have been following this thread and would be interested a 48 v battery system. My email is sgjertson@gmail.comI have an extra 500 3.2 v 90 ah cylinders with bms devices and chargers. We are using big prismatic cells for our next high voltage battery project I could duplicate my 48 v lifepo4 set up and charge only material cost if you are interested I will get you some pictures. We are in San DiegoBest regards,Larry SchmitzOn Friday, May 22, 2020, 5:21 AM, Larry Brown <elcapitanbrown@gmail.com> wrote:
Mine is Thunderstruck too. For your size boat you can go with air cooled but need to make sure to get and engine compartment fan to circulate air. No more water intake to get clogged with sea grass or some idiot's shopping bag floating by as you motor. One of the beauties of the system. It should push you just fine. I use a couple eu2000 generators as backup for long distance trips but for day trips where you need a couple hours at most you can get by on batteries.Anyway, good luck.Do you have a link for the batteries you had success with? There are so many on offer and it seems quite hard to find much info about each company except for the us based ones and those are all twice as expensive (I recognize that this is possibly for good reasons).On May 21, 2020, at 18:14, L Schmitz via groups.io <terminalift=yahoo.com@groups.io> wrote:
I have had good luck with my 10kw thunderstruck kit too. First installed 4 agm batteries 12v 220 ah. Then after 2 years replaced with lifepo4. An excellent upgrade I assembled 4 battery boxes with 3.2v 90ah cylinders. Each box 4P4S Then installed an ant bms for balancing. The monitor is very good for checking your system. If you decide to assemble your own battery system invest in a Flir Heat sensor. The Flir connects to your I phone. You aim it at your wiring assembly under load. It detects hot spot areas of concern in your connections. Battery, contactor ,controller and motor connections. 48 v 360 ah gives plenty of run time at 40 to 90 amp load.Best regards,Larry SchmitzOn Thursday, May 21, 2020, 4:16 PM, Reuben Trane via groups.io <rjtrane=me.com@groups.io> wrote:
Go to thunderstruck-ev.com and look at their kits. I purchased 2 ea for my 12m Power cat. For your needs a 5kW to 10kW motor should do the job. Hard part is figuring out the reduction. I chose 3:1 to get a max prop RPM of 800.48Vdc woks best. If it's in your budget assemble a battery from LiFePo4 cellsFeel free to ask me about my installation.Reuben
_._,_._,_
Groups.io Links:
You receive all messages sent to this group.
View/Reply Online (#30545) | Reply To Group | Reply To Sender | Mute This Topic | New Topic
Your Subscription | Contact Group Owner | Unsubscribe [newarmyguitar24@gmail.com]
_._,_._,_
No comments:
Post a Comment